IP Command or nmcli? Which One Should You Use for Linux Networking?

If you’re still using ifconfig, stop. This command was officially deprecated in Linux kernel 2.4 - way back in 2001.

When it comes to managing network configurations in Linux today, two popular tools stand out: ip and nmcli.

Both are powerful, but they serve different purposes and are used in different scenarios.

Picking the wrong one can make your job harder than it needs to be.

If you’re new to Linux or just trying to figure out which tool to use, this article is for you.

What is the ip Command?

The ip command is a low-level tool used to manage and configure network interfaces, routes, and other networking settings.

It is part of the iproute2 package and is considered the modern replacement for older tools like ifconfig.

Think of the ip command as a “manual” tool for networking. It gives you full control over your network settings, but you need to know exactly what you’re doing.

One thing to keep in mind is that the ip command only makes temporary changes to network settings-it doesn’t update any configuration files. This means that any changes made with ip will be lost after a reboot.

If you want your changes to persist, you must save them in the appropriate configuration files or use tools like nmcli (on RHEL) or Netplan (on Ubuntu).

See also: Mastering the Linux Command Line — Your Complete Free Training Guide

$ ip a
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
       valid_lft forever preferred_lft forever
2: ens192: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 1000
    link/ether 00:50:56:81:47:9d brd ff:ff:ff:ff:ff:ff
    inet 10.254.175.59/25 brd 10.254.175.127 scope global noprefixroute ens192
       valid_lft forever preferred_lft forever
3: docker0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue state DOWN group default
    link/ether 02:42:b9:14:7a:96 brd ff:ff:ff:ff:ff:ff
    inet 172.17.0.1/16 brd 172.17.255.255 scope global docker0
       valid_lft forever preferred_lft forever

Why ip Isn’t Always Enough

Don’t get me wrong - ip is a powerhouse for managing network configurations in Linux. It’s fast, versatile, and far better than the outdated ifconfig.

But here’s the problem: it has its limits. If you’ve ever struggled with networking in Linux, you’ve probably hit one (or more) of these roadblocks:

• 🚧 Verbose Output - ip dumps a lot of information at once, making it hard to parse when troubleshooting. Its output requires extra effort to read and debug.
• ⚠️ No High-Level Abstractions - Need to manage Wi-Fi, VPNs, or bonding interfaces? ip won’t do it alone.
• 📊 Limited Automation - While powerful in scripts, ip lacks built-in profiles or persistent configurations.
• 📝 Syntax Overload - Commands like ip route add 192.168.1.0/24 via 10.0.0.1 dev eth0 get unwieldy fast, especially in complex setups.

Common Use Cases for ip Command – Temporary Change:

To view all network interfaces and their IP addresses, use:

ip addr

To enable or disable a specific network interface, use:

ip link set eth0 up

ip link set eth0 down

To manually assign or remove an IP address from an interface, use:

ip addr add 192.168.1.100/24 dev eth0

ip addr del 192.168.1.100/24 dev eth0

To display the current routing table, use:

ip route

To add a route to a specific network, use:

ip route add 192.168.2.0/24 via 192.168.1.1

Key Features of ip Command:

• Low-level control: You can configure almost every aspect of networking.
• No dependencies: It works without requiring any additional services or daemons.
• Manual configuration: Changes made with ip are not persistent (they reset after a reboot unless saved elsewhere).

What is nmcli?

nmcli (NetworkManager Command Line Interface) is a high-level tool used to interact with NetworkManager, a service that manages network connections on Linux.

It simplifies network configuration by automating many tasks.

Think of nmcli as a “smart assistant” for networking. It works with NetworkManager to handle complex configurations, making it easier for users to manage networks without diving into the details.

nmcli -t -f IP4.ADDRESS,IP4.GATEWAY device show

📌 Example Output

IP4.ADDRESS[1]:192.168.1.100/24
IP4.GATEWAY:192.168.1.1

nmcli provides structured, human-readable output, making troubleshooting faster and easier.

Why nmcli Isn’t perfect

No doubt, nmcli is a game-changer for Linux networking. It brings NetworkManager to the command line, making it easier to configure Wi-Fi, VPNs, and connections without digging into config files.

But here’s the problem: it’s not perfect. If you’ve ever tried using nmcli, you might have run into these frustrations:

• 🖥 Too Abstract - While nmcli is great for managing profiles, it hides the raw networking details that tools like ip expose.
• 🔄 Not Always Available - nmcli relies on NetworkManager, which isn’t installed by default on minimal server setups.
• ⚡ Slower Than ip – Since nmcli interacts with NetworkManager, it adds an extra layer compared to the direct approach of ip.

If any of this sounds familiar, you might want to rethink when and where you use nmcli.

Common Use Cases for nmcli - Permanent Change:

To view all active and saved network connections, use:

nmcli connection show

To connect to a Wi-Fi network, use:

nmcli device wifi connect "WiFi-Name" password "WiFi-Password"

To create a new Ethernet connection with a static IP, use:

nmcli connection add type ethernet ifname eth0 con-name "MyConnection" ip4 192.168.1.100/24 gw4 192.168.1.1

To update the IP address of an existing connection, use:

nmcli connection modify "MyConnection" ipv4.addresses 192.168.1.200/24

To enable or disable a specific interface, use:

nmcli device connect eth0

nmcli device disconnect eth0

You can also change network configurations by NetworkManager configuration file:

/etc/NetworkManager/system-connections/.nmconnection

Find your connection file by running:

ls /etc/NetworkManager/system-connections/

It should show a file like eth0.nmconnection.

Edit the configuration file:

sudo nano /etc/NetworkManager/system-connections/eth0.nmconnection

Modify or add the following:

[ipv4]
method=manual
addresses=192.168.1.100/24
gateway=192.168.1.1
dns=8.8.8.8;8.8.4.4;

Restart NetworkManager to apply changes:

sudo systemctl restart NetworkManager

Key Features of nmcli:

• High-level abstraction: It simplifies networking tasks by automating configurations.
• Persistent changes: Configurations made with nmcli are saved and persist after a reboot.
• Integration with NetworkManager: It works seamlessly with the NetworkManager service to manage connections.

Key Differences Between ip and nmcli

Feature	ip Command	nmcli Command
Level	Low-level	High-level
Persistence	Temporary (unless saved manually)	Persistent (saves to NetworkManager)
Complexity	Requires more manual configuration	Simplifies configuration through automation
Use Cases	Fine-grained control, temporary changes, troubleshooting	Managing saved connections, simpler approach, persistent configs
Dependencies	None	NetworkManager service
Output	Verbose, requires parsing	Structured, human-readable
Wi-Fi/VPN	Limited built-in support	Manages through NetworkManager

When to Use ip vs. nmcli

Use ip When:

• You need fine-grained control over network settings.
• NetworkManager is not installed or running on your system.
• You’re troubleshooting or making temporary changes.

Use nmcli When:

• You want to manage saved network connections (e.g., Wi-Fi, Ethernet).
• You prefer a simpler, more automated approach to networking.
• You need persistent configurations that survive reboots.

Example Scenarios

Scenario 1: Assign a Temporary IP Address

If you need to quickly assign an IP address to an interface for testing, use the ip command:

ip addr add 192.168.1.100/24 dev eth0

Scenario 2: Connect to a Wi-Fi Network

If you want to connect to a Wi-Fi network and save the configuration for future use, use nmcli:

nmcli device wifi connect "MyWiFi" password "MyPassword"

Scenario 3: View All Active Connections

To see all active and saved connections, use nmcli:

nmcli connection show

Scenario 4: View Current IP Addresses

To check the current IP addresses of all interfaces, use the ip command:

ip addr

Conclusion

Both ip and nmcli are essential tools for managing networks in Linux, but they serve different purposes. If you need precise, low-level control, go with the ip command. If you want a more user-friendly, high-level approach, nmcli is the way to go.

By understanding the strengths of each tool, you can choose the right one for your specific networking needs. Whether you’re a Linux beginner or an experienced sysadmin, mastering both tools will make you a networking pro!